Mcculloch Brand New Oil Cap For Mac

Picked this up at a garage sale today. It looks to have spent the last 30 years on a shelf, brought down only to cut the occassional branch or two. The owner said it didn't run and it probably just needed a 'carburetor cleaning'. I didn't even try starting it until I had gotten it home and gave it a good going over. Everything looks to be original and in excellent shape.very tight compression and a piston that looks brand new. After draining the gas and putting in some fresh, (28:1) the thing fired right up.

Mcculloch Brand New Oil Cap For Machines

Cuts like a champ too (for a 32cc saw that is). Automatic oiler with manual override. Judging by the serial number it looks to be a late production saw, probably circa 1973/74 or so judging by the '13-' prefix. Check out the original bar cover Here's the specs.

I knew these saws but worked with the heavier Poulan 25s at that time. What ruined them, and you be careful- Is the first time you jerked out the starter rope and disassembled it it was easy to not get the screws inthe right holes. The v-clips the screws go into come loose if the screws holding the halves together slacken. Then the v- clips bounces around inside while running, sticks to the flywheel magnets, rides around and cleaves the coil pack from the cylinder! I have two of them sitting on shelves, now.

And parts may be very hard to come. If you kill the cylinder. I knew these saws but worked with the heavier Poulan 25s at that time. What ruined them, and you be careful- Is the first time you jerked out the starter rope and disassembled it it was easy to not get the screws inthe right holes. The v-clips the screws go into come loose if the screws holding the halves together slacken. Then the v- clips bounces around inside while running, sticks to the flywheel magnets, rides around and cleaves the coil pack from the cylinder!

I have two of them sitting on shelves, now. And parts may be very hard to come. If you kill the cylinder. Click to expand.Thanks for the tip, I'll watch out for that.

Mcculloch Brand New Oil Cap For Machine

The thing looks like it's hardly (if ever) been apart before. Even the o-rings on the gas and oil caps and air filter knob look like new. The thing must have been sitting in a nicer garage than mine The air filter looks original too, and in good shape. There is a little uneven wear on the bar, so I just flipped it for now.as I'm hesitant to file the bar in case I decide to sell it and the buyer wants it 'virgin'. Should I even be concerned with ruining it's value.and is there even any value to them?

(Yes, the claim is that when introduced in 1968, the power mac 6 was the lightest chainsaw ever made.8.5 lbs fueled up and ready to go.) Did I mention that these things are loud? The 'muffler' is pretty much just an empty metal box.funny considering today's chainsaw mufflers Thanks.

Click to expand.If it's been sitting a while, remove the plug and slowly pull the recoil until the piston is at the top of the cylinder. Pour a capful of oil in the cylinder and let it sit a few minutes. Pull the recoil like normal to blow the oil out. Check to see if it's got spark. If it doesn't have spark, you'll have to access the flywheel and points to clean and set them.

Mcculloch Brand New Oil Cap For Mac 2017

As best I can remember, we always ran 32:1 or 40:1 in my grandfather's PM6. I need to get that one running again, I think it was the first saw I ever used. I figured that pic mod thing out after I posted the dang pic twice. My son is in the cities in school, but I'm way over in western MN. I got the air filter out and cleaned. Been watching them catch that Boston creep, mostly.

I have to figure out the chain tension, too. It hangs loose at the bottom, there must be a tensioner in there.

I have a dremel with chainsaw sharpening. And I think I have some other chainsaw sharpening tools in the shop. I want to get it clean. New oil and gas, air filter, check the plug, make sure the chain is on right, sharp I may be ignorant but I'm methodical! In fact, I know this isn't going to be able to do the job. So I bought a Husqvarna 18'. Should have found this place first and gotten some advice there, but the word was Sioux Falls was gouging prices on chainsaws after the ice storm, so I went amazon and got a decent price.

I have to wait for the snow and ice to melt. Get ropes to tie the ladder up to the trees. I'm figuring on hoisting the saw up by ropes after I climb up and get solid. And I have to get whatever goop and paraphrenalia that the trees need for healing. Plenty of time to get the saw working and not in killya mode. Read the new manual.

Probably be back in here for tips on that as well. I'm going to try to do my own, then do neighbors cheap as heck just to try to offset the saw price a bit. Probably sell the big one if I can recoup the diff between used and new. Was just for the grapes and bushes and a little branch trimming so if it works out I'll keep it. I need all this like a hole in the head. Nerve damage to my right hand makes my guitar playing totally suck, but I can hold a saw if I'm careful and patient.

New shoes helped my gout. Toothache taken care of tuesday. Happy birthday to me.L. I'll be glad to get back in the shop and into my 1935 Coronado radio. Gotta look on the bright side.:bang.